Month: February 2018

Uncategorized

Insulation Systems for Low Slope Roofing

Low slope Roofs generally range from almost flat to 4-over-12. Deep trusses or beams that are separated from the roof joists are used to frame these roofs. Since the area between the ceiling joists and the sheathing is limited, it can be challenging to insulate a low slope roof properly.

While some builders use the same insulation methods that they would use for a big attic, they should have different tactics. For a vented roof, it is important that it is unvented first to protect the attic from the moisture-laden air. An unvented roof can be efficiently insulated in numerous ways from the interior or exterior or both.

Fiberglass or Cellulose

When it comes to low sloped roofs, ventilation does not work in the same way as it does in steeply sloped roofs, as the air does not travel from the eaves towards the top. This is why ridge or turbine vents are useless when it comes to low slope roof systems.

If there is a space of at least 18 inches between the roof sheathing and the top-floor ceiling, fiberglass or cellulose can be used for insulation and ventilation. This system only works if an adequately sized cupola is included in the middle of the roof.

Closed-cell foam and Vapor-permeable insulation

It is much easier to insulate unvented roofs and there are a few ways you can do it:

  • Exterior rigid foam: A thick layer, that is minimum 6 inches, of rigid-foam, is installed on top of the roof sheathing
  • Exterior rigid foam paired with interior insulation: A normal layer, about 2-4 inches, of rigid-foam is installed on top of the roof sheathing and that is accompanied with an air-permeable interior insulation (for e.g. fiberglass or cellulose) below the roof sheathing.
  • Exterior closed-cell foam: Closed-cell polyurethane foam is sprayed over the roof sheathing and is supplemented by an air-permeable insulation underneath the roof sheathing.
  • Interior closed-cell foam: Closed-cell polyurethane foam is sprayed on the bottom side of the roof sheathing
  • Interior closed-cell foam pair with an air-permeable insulation: Closed-cell polyurethane foam is sprayed on the bottom side of the roof sheathing and another layer of interior insulation, like blown-in fiberglass or cellulose, touching the cured foam, supplements this insulation.

Note: It is important to make sure that the foam used is adequately thick and can prevent the roof sheathing from dropping below the dew point in winters when installing both closed-cell foam and vapor-permeable insulation together.

Out of the several ways you can insulate a shallow roof, it is always easier to insulate the exterior. No matter which method is used, it is important that the insulation amount achieves the R-values required by the local code.

Uncategorized

Safety 101: Roof Rail Systems

The most effective threat managed by a service roof staff member is reducing the roofing, which could commonly create lasting injuries along with casualty. It is, as a result, required to secure these personnel from this risk as well as autumn safety and security must be executed inning accordance with the structure’s layout. Things can get even more interesting when putting up a different types of roofing system, such as Tesla’s solar powered roofs. 

Guardrails:

Guardrails are a sort of roofing system covering safety and security as well as safety and also safety and security system that is easy as well as after they get set up, the rails use a physical barricade to stay clear of the employees from lessening the roofing. OSHA ask for these rails to have a leading rail that mosts likely to the very least 39 to 45 inches high, a mid rail, along with a toe board to stop points from sliding down the roof as well as putting a threat to the personnel listed below. A guardrail needs to have the ability to hold up versus a marginal weight of 200lb acting in any type of sort of standards, at any kind of kind of kind of spot along the top side. These security rails are commonly put in the training place and the system typically trusts the nature of the side of the roof covering to be proper for protecting the challenges.

As a guardrail assurances that fall threats are absolutely gotten rid of, there is no need for a safety display screen or employee to adhere to the called for of fall security and security.

Generally, guardrails are used together with an additional system of loss defense, such individual fall agitation system.

In order to use this loss defense system in a secure ways, a wonderful training as well as installation regarding this system along with complying with the demands of loss protection while safeguarding the rails, along with eliminating them are necessary.

Setting up the security and protection of commercial roof tasks is extremely vital. It is needed that the site is checked out in order to technique and also exercise the preventative measure and also make sure that the employees are supplied with all the gadgets, recommendations, and aid that they need to secure themselves from loss threats.